·
7 min read

Ask any IT team what they regret about their last office move, and cabling comes up more often than you would expect. Not the switches or the Wi-Fi, but the cables. The meeting room with a single network point. The new access points that need more power than the old cable runs were planned for. The ceiling full of unlabelled blue wires that nobody wants to touch.
Cabling is the part of your network you install once and live with for years. Switches, firewalls and laptops get replaced every few years, while the cables in your walls and ceilings usually stay for a decade or more. Getting them right at the start costs far less than opening up ceilings later.
This guide covers the decisions that matter most when planning structured cabling for an office: which cable to choose, where fiber fits, and what to agree on before an installer starts work.
What structured cabling actually means
Structured cabling is an organised, standards-based cabling system, as opposed to cables run point to point whenever a need comes up. Every desk, access point and camera connects back to patch panels in a rack, through a planned route, with every cable labelled and tested. Professional installations generally follow the TIA-568 or ISO/IEC 11801 standards, which define how cables are run, terminated and tested.
The practical benefit is simple. When something changes, you move a patch cord in the rack instead of pulling a new cable through the ceiling.
Cat6 vs Cat6A: the decision most offices face
For copper cabling to desks and devices, the choice today is usually between Cat6 and Cat6A.
Cat6 comfortably supports 1 Gbps over the full 100-metre channel, but supports 10 Gbps only over shorter runs, typically up to around 55 metres. It is thinner, easier to install and cheaper. For an office where desks need standard connections and cable runs are short, it is still a sensible choice.
Cat6A supports 10 Gbps over the full 100 metres, resists interference between neighbouring cables better, and copes better with the heat that builds up when bundled cables carry power. It is thicker, needs more room in trays and conduits, and costs more per metre.
Our rule of thumb: use Cat6A for Wi-Fi access points, for any cabling you expect to keep for ten years or more, and wherever runs are long. Newer access points can need connections faster than 1 Gbps and more power over the cable than older models, and Cat6A gives you that headroom. Cat6 can still be fine for standard desk points in a smaller office with short runs.
Where fiber fits
Copper handles the last stretch to devices. Fiber is the backbone: it connects the main rack to racks on other floors, links server rooms, and joins buildings on a campus.
Fiber carries much higher speeds over much longer distances and is not affected by electrical interference. Multimode fiber (OM3 or OM4) is the usual choice inside a building, while single-mode fiber is used for longer distances, such as between buildings. If your office spans more than one floor, plan a fiber backbone from the start, even if you only use part of its capacity today.
Seven things to plan before installation starts
Count points per desk, not per person. One cable per desk is rarely enough once you add a desk phone, a docking station or a second device. Many offices plan two points per desk.
Plan for access points, cameras and screens. Wi-Fi access points, CCTV cameras, meeting room displays and access control readers all need their own cables, usually in the ceiling.
Leave room to grow. Spare ports in the patch panel and spare space in cable trays cost little at installation and a lot to add later.
Keep data and power apart. Run network cables away from electrical cables, lighting and machinery to avoid interference, and use proper trays or containment rather than loose bundles.
Respect the 100-metre limit. A copper link from the rack to a device should not exceed 100 metres, including patch cords. If parts of the office are further away, plan a second rack connected by fiber.
Label everything. Every cable should carry the same label at both ends, matching a drawing of the floor. It turns a two-hour fault hunt into a two-minute check.
Ask for test reports. Every cable should be tested with a certification tester after installation, and you should receive the results. Untested cabling is a guess.
Common mistakes we see
Cables run without a plan and plugged straight into switches, with no patch panels.
Cheap cable or connectors used to save cost, causing intermittent faults that are hard to trace.
Too many cables bundled tightly in hot ceiling spaces, especially when they carry power to access points and cameras.
No drawings or records, so nobody knows which port serves which desk.
Cabling left until the end of an office fit-out, when ceilings are closed and routes are hard to reach.
Questions we hear often
Is Cat6 enough for a new office in 2026?
For standard desk connections with short runs, often yes. For Wi-Fi access points and long-term infrastructure, Cat6A is the safer choice, because it supports 10 Gbps over the full distance and leaves room for newer access points.
How long does structured cabling last?
Well-installed structured cabling commonly serves for 10 to 15 years or more, far longer than the equipment connected to it. That is why it pays to choose the cable category for future needs, not just today's.
Can cabling be done while the office is working?
Yes, with planning. Work can be scheduled in sections, after office hours or on weekends, so teams keep working while new cable runs are installed and tested.
How AYSIT can help
AYSIT Solutions plans, installs and supports structured cabling and passive networking for businesses across Hyderabad, Chennai and Bengaluru, from copper cabling to desks and access points to fiber backbones between floors and buildings. If you are planning a new office, an expansion or a clean-up of existing cabling, our team can survey the site and recommend the right design.
Read more about our networking solutions, or contact us to plan your office cabling.


